In this article, Taimienphi.vn continues to guide how to use Auto-Tune to adjust the voice better for you to use this uto-Tune software more effectively. Combined with that, Taimienphi.vn will share the features of the tools for you to choose appropriate use such as Line, Curve, Note, Arrow …
As mentioned in the previous article, Auto Tune is considered the recording industry standard for better vocal adjustment. Readers refer to the instructions using Tune to adjust vocals better part 2 See below for how to make Auto-Tune adjustments.
Use Auto-Tune to adjust vocals better than part 2
Tutorial How to use Auto Tune to adjust vocals better than Part 1
If you do not have Auto-Tune installed on your computer and do not have any knowledge of this software. You can download and Install Auto Tune on the computer and then refer to the instruction on how to use Auto-Tune to adjust the voice better in Part 1 first.
How to use Auto-Tune to adjust vocals better part 2
Track Pitch in Auto-Tune
The first step is to take a picture or Track Pitch audio track in Auto-Tune to analyze and chart the audio notes. This allows Auto-Tune to respond not only to quick response, but also to append the modified note, which cannot be done in Auto Mode, because it runs in real time. To begin:
– Click the button Track Pitch. This button will turn red when activating Track Pitch.
– Play music: Play your song from start to finish, or in parts. As long as all the information that needs to be adjusted is tracked, you may continue.
– Turn off Track Pitch button: Needed to start adjustment.
You now have 2 options to adjust. You can draw or automatically create lines or notes. The difference is that the notes are usually easier to handle and handle a sound area as a block or note and a line or curve allows you to handle the curves in between specific notes.
Here are some tools to get started:
– Line tool Used to draw multi-line lines on a pitch chart. Usually this tool is used if you want to keep straight lines or curves from one pitch to another.
– Curve tool Used if you want to draw freely in pitch. This tool is quite difficult to use.
– Tool Note used to draw notes.
– Arrow tool Most commonly used, this is the tool used to select and edit existing lines or notes.
– Scissors tool Used to cut existing lines or notes in separate sections to edit each line.
– Magnifying glass used to zoom. Just click and drag the box around the content you want to enlarge.
– I-Beam tool Used to select a time zone used to edit or create data. This is also one of the frequently used tools.
– Hand tool used to move the screen. Click and hold the area on the screen, and drag the screen to the area you want to view.
Manually edit / drag lines and notes in Auto-Tune
In the example below, after capturing (Track Pick) vocal into Auto-Tune, next step select Line tool, click Snap to Note to tie any segment of a straight line to a specific note. When you click the last segment, you have to double click to end the line.
After drawing, this line is still selected and retune speed can be set for this line independently of the others. If for some reason the line is not selected, use the Arrow tool, then click on the line to select again, and you can adjust the retune speed. The advantage of using the Line tool is to keep the curves from note to note.
In the example below, the Note tool is selected, then use the tool to draw a note. Drawing the note from the position on the key or switching to the desired key at the beginning and end of the note will yield the best results. The advantage of using the Notes tool is that it is possible to move notes from one pitch to another, much easier than moving a line.
Automatically create lines and notes in Auto-Tune
Choose an area: Using the I-Beam tool, select the area where you want to make notes or lines.
Next scroll down to the plug-in located next to Track Pitch, which is optional for Make Curve and Make Notes to create notes or curves.
– Make Curve: Click on the button Make Curve to automatically draw curves, exactly match the pitches captured from the previous Track Pitch function. As you can see on the right side, green lines overlapping the pitch are detected, and anchor points on either side of each event are detected. These anchor points can move one by one, by clicking and selecting each point, then dragging each anchor point up or down. This is especially useful in keys. You can also use the Arrow tool to perform operations for these points.
In the example below, the area is selected using the I-Beam tool, then using the Arrow tool, the curves are moved from pitch to pitch, the notes remain intact. If only a part of the curve or line is moved, that line can be split into 2 segments by clicking on the split point you want using the Scissors tool. Now you can control each segment.
In this example, the Make Notes button is selected after selecting the same area described above. The advantage of this approach is to adjust or manipulate the notes being maintained and the curves between the notes to be retained.
To correct these notes, use the Arrow tool. For best results, drag the edges of each note to the intersection points, where the original audio position is turned on or over. By starting and stopping the adjustment on these adjusted points, the sound will be clearer and more realistic.
Thus in the article Instructions on how to use Auto-Tune to adjust the voice better than Part 2 above Taimienphi.vn showed you how to use Auto-Tune to adjust the voice better. Hopefully the above knowledge is enough to help you start using and adjusting your vocals with Auto-Tune.